125 101215 f38 series conductive polymer, miniature, undertab solid electrolytic chip capacitors lead-free compatible component marking m case s case *capacitance code a j s rated voltage code rated voltage code packaging special code axe = rated temperature 60oc and h dimension 1.0mm max. axeh3 = rated temperature 60c and h dimension 1.0mm max., low esr lzt = rated temperature 60oc only ah1, ah2, ah3 = low esr features ? conductive polymer electrode ? benign failure mode under recommended use conditions ? compliant to the rohs2 directive 2011/65/eu ? smd facedown ? small and low profile ? high volumetric efficiency applications ? smartphone ? tablet pc ? wireless module ? portable game case dimensions: millimeters (inches) code l w 1 w 2 hs 1 s 2 m 1.60 0.85 0.650.10 0.800.10 *1 0.500.10 0.600.10 (0.063 ) (0.033 ) (0.0260.004) (0.0310.004) (0.0200.004) (0.0240.004) s 2.00 1.25 0.900.10 0.800.10 0.500.10 1.000.10 (0.079 ) (0.049 ) (0.0350.004) (0.0310.004) (0.0200.004) (0.0390.004) +0.20 -0.10 +0.008 -0.004 +0.20 -0.10 +0.008 -0.004 +0.20 -0.10 +0.008 -0.004 +0.20 -0.10 +0.008 -0.004 reel dia tape width ( 180) (mm) a8 f38 type 1a rated voltage 225 capacitance code pf code: 1st two digits represent significant figures, 3rd digit represents multiplier (number of zeros to follow) m tolerance m = 20% m case size see table above how to order category temperature range: -55 to +105c rated temperature: +85c (*2) capacitance tolerance: 20% at 120hz dissipation factor: refer to next page (120hz) esr 100khz: refer to next page (120hz) leakage current: refer to next page at 20oc after application of rated voltage for 5 minutes provided that: after 5 minutes application of rated voltage, leakage current at 105c 10 times or less than 20oc specified value. technical specifications *1 f380j476mmaaxe: 1.0mm max. *2 f380j476mmaaxe: rated temperature +60oc surge, endurance test temperature +60oc
126 101215 f38 series conductive polymer, miniature, undertab solid electrolytic chip capacitors capacitance rated voltage *cap f code 4v (0g) 6.3v (0j) 10v (1a) code 2.2 225 m C 4.7 475 m C 10 106 m/m(ah1,ah2) m/m(ah1) a 22 226 m/m(ah3,ah1)/s/s(ah1) s j 33 336 m**/s n 47 476 m* 4 /m* 4 (h3)/s/s(ah1) s 68 686 s** w 100 107 s* a capacitance and rated voltage range (letter denotes case size) available ratings, (low esr) *codes under development C subject to change *4 rated temperature 60 and h dimension 1.0mm max only. please contact avx when you need detail spec. **rated temperature 60oc only. please contact avx when you need detail spec. please contact to your local avx sales office when these series are being designed in your application. ratings & part number reference the corelations among rated voltage, surge voltage and derated voltage item all case (%) damp heat, steady state -20 to +30 rapid change of temperature 20 resistance soldering heat 20 surge 20 endurance 20 f38 (standard) f38-axe rated voltage (v) 6.3 10 6.3 60oc surge voltage (v) - - 8 85oc surge voltage (v) 8 13 - 85oc derated voltage (v) - - 4.5 105oc derated voltage (v) 5 8 3.3 *3: c/c marked * rated leakage df esr 100khz rms *3 avx case capacitance voltage current (%) (m) current c/c part no. size (f) (v) (a) @ 120hz @ 100khz (ma) (%) 20oc 6.3 volt F380J106MMA m 10 6.3 10.0 8 500 224 * F380J106MMAah1 m 10 6.3 10.0 8 300 289 * F380J106MMAah2 m 10 6.3 10.0 8 200 354 * f380j226mma m 22 6.3 13.9 10 500 224 * f380j226mmaah3 m 22 6.3 13.9 10 300 289 * f380j226mmaah1 m 22 6.3 13.9 10 200 354 * f380j226msa s 22 6.3 13.9 10 200 474 * f380j226msaah1 s 22 6.3 13.9 10 150 548 * f380j336mmalzt m 33 6.3 41.6 10 500 224 * f380j336msa s 33 6.3 20.8 10 200 474 * f380j476mmaaxe *4 m 47 6.3 59.2 10 500 224 * f380j476mmaaxeh3 m 47 6.3 59.2 10 300 289 * f380j476msa s 47 6.3 29.6 10 200 474 * f380j476msaah1 s 47 6.3 29.6 10 150 548 * f380j686msalzt s 68 6.3 86.0 10 200 474 * 10 volt f381a225mma m 2.2 10 10.0 6 500 224 * f381a475mma m 4.7 10 10.0 6 500 224 * f381a106mma m 10 10 10.0 15 500 224 * f381a106mmaah1 m 10 10 10.0 15 300 289 * f381a226msa s 22 10 22.0 10 200 474 *
127 101215 f38 series conductive polymer, miniature, undertab solid electrolytic chip capacitors test f38 series (temperature range -55oc to +105oc) condition at 40c, 90 to 95% r.h., 500 hours (no voltage applied) damp heat capacitance change ........... refer to page 126 (*3) (steady state) dissipation factor ................ 200% or less of initial specified value leakage current .................. 300% or less of initial specified value at -55c / +105c, 30 minutes each, 5 cycles temperature cycles capacitance change ........... refer to page 126 (*3) dissipation factor ................ 200% or less of initial specified value leakage current .................. 400% or less of initial specified value 10 seconds reflow at 240c resistance to capacitance change ........... refer to page 126 (*3) soldering heat dissipation factor ................ 200% or less of initial specified value leakage current .................. 300% or less of initial specified value after application of surge voltage in series with a 1k resistor at the rate of 30 seconds on, 30 seconds off, for 1000 successive test cycles at 85oc (*2), capacitors shall meet the characteristic requirements in the table above. surge capacitance change ........... refer to page 126 (*3) dissipation factor ................ 200% or less of initial specified value leakage current .................. 300% or less of initial specified value after 1000 hours application of rated voltage in series with a 3 resistor at 85c (*2), capacitors shall meet the characteristic requirements in the table above. endurance capacitance change ........... refer to page 126 (*3) dissipation factor ................ 200% or less of initial specified value leakage current .................. 400% or less of initial specified value shear test after applying the pressure load of 5n for 101 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on a substrate, there shall be found neither exfoliation nor its sign at the terminal electrode. terminal strength keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied with a specified jig at the center of substrate so that the substrate may bend by 1mm as illustrated. then, there shall be found no remarkable abnormality on the capacitor terminals. qualification table notice: design, specifications are subject to change without notice. *2 f380j476mmaaxe: rated temperature +60oc surge, endurance test temperature +60oc
|
